Construction of the fountain in the country with their own hands

For any owner the appearance of the dacha or yard is of great importance. Its design can be handled by experts, but, if desired, you can do it yourself. The fountain will be a good decoration of the yard or the plot. It can also be built with your own hands on your own project.

Types of fountains

Fountains for giving happen different types. They are subdivided into types: according to the device, according to the appearance, according to the peculiarities of the work, etc. According to the way the device is used, summer fountains are circulation and flow, they are also called "Roman".

Circulating assume the water cycle. Water fills a specific tank (bowl, vase, water reservoir) and with the help of a pump is fed to a device from which it directly beats a stream of water.

Everything is arranged so that the outgoing water enters the tank and is swinging up again.Thus, the device does not involve the supply of water from a water supply system or a well. The only thing that is necessary is to add water to a certain label, since it tends to evaporate or splash.

Flowing Fountains arranged with the use of water supply (wells) and sewage. Water flows up, falls down and goes down the drain. The way, of course, irrational, but such fountains have several advantages:

• esthetic appearance;
• drinking water;
• the possibility of using water for watering lawns, flower beds, shrubs and trees.

By appearance and features, you can also classify fountains into single-level and multi-level, single and group, jet, waterfall, cascade, in the form of a ring or tulip, dancing, singing, colored, with a pond, with a reservoir, etc.

Choosing the right place

If you decide to build a fountain on the site with your own hands, then, first of all, choose a suitable place for this. In the case of a pond or pond at the dacha, the choice of location is obvious.Where the pond is located - there will be a fountain. The pond device, of course, will have to be modified, corrected, but the basis will remain.

If you start from scratch, then the place should be chosen, carefully weighing all the pros and cons. Hand-made garden fountains perform various functions: they humidify the air in the garden, which is useful for trees, create cool conditions, can be used for irrigation, etc.

For this reason, you need to choose a place so that the fountain not only brings aesthetic pleasure, but also is useful. A suitable place for arrangement will be an open area between trees, shrubs or a hedge.

Trees and bushes should not hang over the pond or reservoir, so that debris does not fall into the water and leaves fall. It is harmful to water filters. Even because of the proximity of the trees, and hence their root system, it is possible that the underground part of the fountain is broken or even destroyed.If in the country grow plants that do not tolerate waterlogging, equip the fountain away from them.

No need to equip the structure in the open sun, because it is fraught with water bloom. There is one more condition: the fountain in the country, made by hand, must be in harmony with the overall design. Everything should be done in the same style. This should be a platform that is clearly visible from the windows of the house and from any part of the courtyard, because you are building a fountain, primarily for aesthetic pleasure.

Preparation of materials for construction

When the place for the fountain and its type has been selected, a project has been developed, it is necessary to determine what materials will be needed for construction. Assume that the project is designed for a circulating jet static fountain with a single discharge of water, i.e. the "Geyser" type.

At home, for the construction of the fountain with their own hands will need cement, sand, gravel, durable plastic film and building facade mesh the size of the building’s diameter (both the film and the mesh must be the same size). In addition, you need a plastic container with a volume of about 50-70 liters, depending on the size of the structure.

If you plan to arrange all the stones, then prepare them immediately.This may be a wild stone of the desired size, cobblestone, granite, large pebbles, etc. To ensure proper operation, you will need a fountain pump.

Pump selection criteria

Depending on the type of fountain you need to choose a pump. For the waterfall, we would choose a surface pump, and since we have a traditional fountain, we choose a submersible one.

As a rule, submersible pumps perfectly perform their function. They are compact, work quietly, they are easy to install and, which is also important, are affordable. Submersible pumps come in different capacities. It is calculated in the amount of pumped water for 1 hour (l / h).

The height of the jet will depend on the pump power. The maximum height is calculated from the diameter of the foot you made. The pump in this case does not need to be selected by the principle "the more powerful the better." We need for the arrangement such that the jet was high enough and that the spray does not fly out beyond the "foot". For giving height of a stream will approach from 80 cm to 1 m.

Manufacturers, as a rule, submit to the instructions a table of the ratio of power and height of the jet. Since we are equipping the "Geyser", then for such a device will need a pump with a capacity of about 7000 l / h.

The principle of installation of the pumping system

The pumping system is installed 10 cm above the bottom on a stand (brick laid or mounting stand). A hose or pipe with water supply is supplied to it. Usually the sprinkler comes complete with a pump, but if it is not there, you can make it yourself.

To do this, you can take the usual pipe of stainless steel. The diameter will depend on the height of the jet and the diameter of the spray of water. For a small fountain of 0.8-1.0 m, a diameter of 2-2.5 inches will suffice. The length will depend on how deeply the pump is submerged. Above the water enough to leave 10-15 cm.

To shape the jet, you can flatten the pipe, roll it up, leaving a hole, drill a few holes, or cut the thread and fasten the desired nozzle. Connect to the pump directly or via an adapter (if necessary).

Installation of the fountain. Step-by-step instruction

Master-class installation of the fountain in the country with their own hands with step-by-step photos found on the Internet is easy. Usually installation takes place in several stages. The arrangement for the selected project includes 10 steps:

1. Prepare a pit. Once you have decided on the project and chose a place, you need to dig a hole of the desired diameter and shape for 1-2 bayonet spade. To level a bottom, to fill up with rubble and to stamp.
2. Make formwork. It is made in the form of a pit with an external and internal border. That is, the inner formwork should be of a smaller diameter, and the outer one should be larger. The shape can be different: round, square, hexagonal or octahedral. Between the sides of the formwork with a total diameter of the fountain 1.5-1.7 m should be 60-70 cm.
3. Construct a harness from reinforcement. This must be done between the inner and outer borders. To do this, it is necessary to cut the steel bar into pieces of the required size, fasten them together with a wire and fasten them to the rods, driven into the ground. The rod should leave the ground at a distance of 20-25 cm above ground level (not pits).

4. Make a concrete solution. For the solution you need 1 bucket of cement, 2 buckets of sand, 2 buckets of rubble, water. To make a homogeneous mass, that is, concrete, will help the concrete mixer.
5. Pour concrete form external. The form is poured to the desired height, it is about 30-35 cm above ground level. The mixture is well leveled. A slope forms inside.
6. Prepare the inside. To do this, remove the external and internal formwork. Below the inner edge level, install a plastic container with a volume of about 50-70 liters. The voids around it should be filled with sand, from above - with rubble almost to the top.
7. To make a waterproofing. To do this, lay a film on top of the entire structure, cutting a slot in the center. Well straighten it.
8. Install the pump. As already mentioned, the pump is installed on a small stand, and not on the bottom of a plastic container. Electricity is supplied to it. Immediately attached itself sprinkler, which comes in a set or made independently (as mentioned above). From above, the pump is covered with a construction mesh according to the diameter of the inner part of the structure. It makes a small slot.
9. Fill the tank. It is filled to the brim with water to ensure proper operation of the pump.
10. Decorate the fountain. To do this, you need to decorate the building on the sides and on top.

Additional equipment and accessories

For the fountain on the site, you can provide different nozzles and change them at will. You can also add lighting and background music.For the purpose of electrical safety, the backlight must be selected reliable.

Care Tips

Maintenance of the design is simple. In the summer, you need to monitor the operation of the pump. If the sound has changed, then the water is supplied poorly, so you need to remove the pump from the tank, clean the filters and the tank itself from sludge, dirt.

Periodically check the water level in the tank. If the level has fallen - add water. For the winter you need to pull out the pump, clean its filters. Empty the container from water, clean and wash it. In addition, the entire structure is better covered with a film that protects against dust and precipitation. As you can see, make a fountain with your own hands and care for him, it is not difficult.

Decor options

You can decorate the finished building in any style that you like. You can use natural materials or purchase ready-made decorative elements. You can decorate the side parts with a wild stone of small size, laying it on the cement mortar. It is better if the stones are multi-colored. In this case, on top of the film and the grid also lay out the stones, large pebbles. You can put on the edges of small statues. Along the perimeter, you can land moisture-loving plants.

The fountain on your site will become a central structure, which will immediately attract attention. A little effort to install it - and it will freshen up in the heat and please you every day.